Useful Links
• Save Water Save Money• Easy URECO Installation
• Maintaining your URECO
• Case Studies
• Technical Downloads
• Why choose URECO?
• Site Map
URECO hygienec urinal outlet device 1.5” EXPOSED INSTALLATION KIT
Ureco has been designed to fit the majority of common urinal bowls with removable outlet connectors. The systemis quick and easy to install, however you must follow these few important steps to create an efficient freeflowing biological urinal system that is easily maintained and odour free. Before starting the installation please ensure that you have the correct install kit for your type
of urinal and the appropriate plumbing tools and skills to complete the installation successfully whilst complying with local water bylaw requirements and maintaining good hygiene.
WASTE PLUMBING INSTALLATION
1) Isolate water supply to cistern Immediately isolate the water supply to the cistern after ensuring the cistern has flushed and is empty.2) Disconnect and remove the existing bottle trap /U-bend from existing urinal outlet at the bottom of the urinal. Dispose of the old outlet from the urinal bowl and remove any old sealant, making sure all surfaces are dry and clean.
3) Install the Ureco outlet. When installing be careful not to over-tighten the outlet nut, in most cases you may need to apply a sealant / sealing compound to ensure a good seal. Ensure the downstream waste pipe work is serviceable before connecting the new Ureco outlet to the new telescopic trap. Once all pipes and traps have been reconnected, check all joints for leakage.
4) Restrict sparge pipe water flow. The Ureco requires a reduced volume of flushing water. Installing the water saving restriction washer within the cistern outlet fitting will ensure sufficient restriction. Once fitted you will notice a large reduction in flushing water velocity which is a unique feature and benefit of the Ureco system, saving water and money. To maximise water savings, we recommend flushing NO more than 2 Litres per urinal per flush. This can be achieved using one or more cistern restriction bags in the cistern.
5) Install Ureco head into new Ureco outlet at the bottom of the urinal pan. It is very important that the Ureco clicks into place securely to ensure a correct fit.
*Please note, The Ureco must be replaced every 3 months to remain effective.
6) Note: If no electronic urinal flush control is fitted please proceed to step (7) otherwise reinstate water supply to the cistern.
FLUSHING TIMER INSTALLATION
7) Electronic Flushing Controls. It is highly recommended that a flushing control is used to maximise the efficiency of the Ureco system. In most cases a basic ES50 timer can be used however in more complex heavily used sites an ES10 flushing control is preferable.
8) Installation of an ES50 flushing control. Remove the adjustable drip control from the end of the fill pipe and fit a 90 degree bend to direct the water into the cistern without splashing. Remove a section of the pipe and fit the solenoid valve whilst referring to the instructions found within the ES50 packaging to suit your system. Push the battery operated ES50 onto the solenoid valve ensuring the three pins are inserted correctly. Please follow the set up procedure in the ES50 instructions. (Please note: In variable use washrooms I.e. Sports Stadiums. please consider the use of a motion sensor flush system such as the ES10).
9) Testing It is highly recommended to check the flushing water flow through the urinal before leaving the site. It is essential that no flushing water “back up” occurs due to poor drainage condition (i.e. Build up of sludge or uric salts).
REMEMBER
1) Isolate water supply & empty cistern
2) Disconnect bottle traps
3) Install Ureco outlet
4) Restrict sparge pipe water flow
5) Install Ureco
7) Install an electronic flushing controls
9) Test System
Once installed you can start saving Money and water.
Product manufactured for HSG UK Ltd
For SALES / SERVICE Call 0800 032 7760
a) Cistern Restriction Bag
b) Flow Restriction Washer
c) URECO Outlet with Nut & Washer
d) Telescopic Bottle Trap
![]()
Head Office: HSG UK Ltd. The Old Printworks, 17 Queen Street, Ilkeston, Derbyshire.
DE7 5GT Company Reg No: 6447301 Registered in England
© HSG UK Ltd - All rights Reserved - HSG UK Hygiene Products
Hygiene Products | Washroom system | Urine Cleaners | Hygiene products supplier
Washroom Services |
Hygiene Systems |
Urinal Cleaning | Urinal Bowl Cleaner
The Ureco

URECO Urinal Outlet
Installation Guide
